DJI Goggles 2 Firmware updates

SparkyFPV · 10 January 2023 19:24

Date: 2022.11.22

What’s New?

Added support to use with DJI O3 Air Unit.
Added support to use Canvas Mode when using with DJI O3 Air Unit.
Added hibernation mode: the goggles will enter hibernation mode after being idle for a long time
(approximately eight minutes) when powered on. Wake up the goggles by pressing the link button.
Optimized the video transmission experience in broadcast mode for both pilot and audience.
Optimized prompts in some scenarios.
Optimized the goggles tutorials

Notes:

Restart the aircraft (or air unit), remote controller, and goggles after the update is complete.
Note that the update may reset various flight parameters such as the RTH altitude and the maximum flight
distance. Before updating, take note of your preferred settings and readjust them after the update.
If update fails, restart the aircraft (or air unit), remote controller, goggles, and DJI Fly or DJI Assistant 2
(Consumer Drones Series) and try again.

SparkyFPV · 10 January 2023 19:25

Date: 2022.12.08

What’s New?

Added support to use with DJI FPV Air Unit Module.
Added support to use Canvas Mode when using with DJI FPV Air Unit Module.
Added support for the following video recording specifications when using with DJI Avata:
2.7K@120fps
1080p@120fps
4K@30fps
2.7K@30fps
1080p@30fps
Added ability to transfer data from the aircraft internal storage to the installed microSD card when using
with DJI Avata.
Added ability to configure the sharpness and noise reduction value.
Added ability to display the channel information on the LED dot matrix display.
Optimized some interface prompts.

Notes:

Restart the aircraft (or air unit), remote controller, and goggles after the update is complete.
Note that the update may reset various flight parameters such as the RTH altitude and the maximum flight
distance. Before updating, take note of your preferred settings and readjust them after the update.
If update fails, restart the aircraft (or air unit), remote controller, goggles, and DJI Fly or DJI Assistant 2
(Consumer Drones Series) and try again.
DJI Goggles 2 Release Notes

SparkyFPV · 10 January 2023 19:30

Goggles V2 Firmware: V01.04.0000

Whats New?

SparkyFPV · 26 July 2023 06:02

V01.07.0000

Now compatible with the DJI FPV

GunjaFPV · 27 July 2023 10:34

Heh just came to post this. Good news, now the 2/integra and V2 compatible with all systems (well FPV systems, not the Mini 3 with the V2/1)

robertspark · 10 August 2023 20:50

I see latest goggles 2 firmware update has support for DJI FPV

should have read the post upwards …

SparkyFPV · 10 August 2023 21:25

SparkyFPV · 2 October 2023 20:44

Date: 2023.09.25

DJI Goggles 2 Firmware: v01.08.0000 ARB 0

DJI Fly App Version: v1.12.0 (iOS & Android)
What’s New
Added support to use with DJI Air 3.
Notes:
Update the firmware of the aircraft, goggles, and motion controller before using for the first time,
otherwise the devices cannot be linked.
Aircraft: Update the firmware using the original remote controller of the aircraft.
Goggles and motion controller: Connect the goggles to a mobile device and run the DJI Fly app. Select
Profile Device Management. Locate the corresponding goggles. Select Firmware Update and follow the
on-screen instructions to update the firmware.
Alternatively, the DJI Assistant 2 (Consumer Drone Series) software can be used on a computer to
update the firmware of the devices separately.
When used with the goggles, only DJI RC Motion 2 is supported for flight control, other remote controllers cannot be used to control the aircraft.
Restart the aircraft, goggles, and motion controller after the firmware update is complete.
Note that the update may reset various flight parameters such as the RTH altitude and the maximum
flight distance. Before updating, take note of your preferred settings and readjust them after the update.
If the update fails, restart the devices and software, and then try again

SparkyFPV · 22 December 2023 11:22

Overview:

What’s New

Notes:

Update the firmware of the aircraft, goggles, and motion controller before using for the first time, otherwise the devices cannot be linked.
Aircraft: Update the firmware using the original remote controller of the aircraft.
Goggles and motion controller: Connect the goggles to a mobile device and run the DJI Fly app. Select Profile > Device Management. Locate the corresponding goggles. Select Firmware Update and follow the on-screen instructions to update the firmware.
Alternatively, the DJI Assistant 2 (Consumer Drone Series) software can be used on a computer to update the firmware of the devices separately.
When used with the goggles, only DJI RC Motion 2 is supported for flight control, other remote controllers cannot be used to control the aircraft.
Restart the aircraft, goggles, and motion controller after the firmware update is complete.
Note that the update may reset various flight parameters such as the RTH altitude and the maximum flight distance. Before updating, take note of your preferred settings and readjust them after the update.
If the update fails, restart the devices and software, and then try again.

SparkyFPV · 28 May 2024 13:40

Overview:

What’s New

Notes:

Update the firmware of the aircraft, goggles, and motion controller before using for the first time, otherwise the devices cannot be linked.
Aircraft: Update the firmware using the original remote controller of the aircraft.
Goggles and motion controller: Connect the goggles to a mobile device and run the DJI Fly app. Select Profile>Device Management. Locate the corresponding goggles. Select Firmware Update and follow the on-screen instructions to update the firmware.
Alternatively, the DJI Assistant 2 (Consumer Drone Series) software can be used on a computer to update the firmware of the devices separately.
When used with the goggles, only DJI RC Motion 2 is supported for flight control, other remote controllers cannot be used to control the aircraft.
Restart the aircraft, goggles, and motion controller after the firmware update is complete.
Note that the update may reset various flight parameters such as the RTH altitude and the maximum flight distance. Before updating, take note of your preferred settings and readjust them after the update.
If the update fails, restart the devices and software, and then try again.