Missed this. Looks very useful.
I just messaged back following the last chat in September 22.
Great to see that he provides free updates.
1 Like
Always does 
Does anyone a current contact number for Sincoder on Telegram? +86 13590379508 is reporting as not availble on Telegram.
Some posts above mention how contact has been established ā¦ around this post.
Thanks @OzoneVibe ā¦ I should have read the thread more closely!
Anyone try any of these options?
disable - turn off all hacks
enable - turn on all hacks
reset - reset to default config
500 on/off - force max height to 500m or not
force_fcc on/off - enable/disable force fcc (drone will ignore country code setting)
rcgps on/off - enable rc gps or not (can not set RTH point to RC location after turn off)
led on/off - turn on/off drone led
atti on/off - turn on/off atti mode
vps on/off - turn on/off all vison sensors
manu on/off - turn on/off manul mode (be carefull)
vled on/off - enable led on/off when record (set led on first)
gps on/off - enable/disable drone gps
CC US/CN/JP/RU/HKā¦ - set drone country code (can disable FCC mode)
droneid on/off - turn on/off droneid (need drone firmware support turn off droneid)
5.8 on/off - enable/disable force 5.8GHz ,disable 2.4G
flog off - delete all drone flight logs (the logs inside drone, logs will be deleted the next time the drone restarts)
landing on/off - enable/disable force landing ( M3 firmware verion <= 900 )
This has been recently updated further to disable the force landing on the Mavic 3 drones when the battery gets low. At the moment you cannot disable the force landing apart from via a modification.
This mod AFAIK turns on FCC mode in the most basic form. So I am a bit confused by the ability to force to use CC US or CC CN etc. to set the drone country code as I assume these just enable FCC mode. Unless they do more?
āDefault controllerā¦400 metres maxā? Crikey, thatās not good. Using a non-FCC DJI RC linked to an Air 2S flying from a jetty some 80 metres from shore I flew it parallel to shore to a small island 2000 metres there and 2000 metres back in West Papua, Indonesia last December, no problem.
Iāve got the key from him today and he said he only gets payment via crypto transfer which i didnāt know anything about it so found someone to do for me , anyway ā¦
At first , couldnāt connect the pc and dji assistant 2 didnāt see the controller so deleted it and downloaded the one named ā consumer drone series ā and it worked. It connected and saw the cotroller.
But the thing i donāt understand is i used someone elseās computer to download the patch and after i finished i deleted everything. If the newer update releases and if i update the controller i will have to reinstall the patch so at that time can i still use the patch i bought on a diffirent computer by downloading again ?
Yes - install again using the same file.
If anyone here says that a new version is released ask him for a new copy.
As it is bound to the serial number actually doesnāt matter if one of us sends it to you either.
just paid Sincoder via the Telegram QR code with USDT. he responded within about 30mins, then was very responsive (minutes).
the hack seems to be installed but after a reboot itās been stuck forever on āSystem is optimizingā. I assume thatās normal and the long time is just because the processor is pretty underpowered - how long does this take?
ah, it seems if you leave USB connected, it might hang there. I disconnected & rebooted (fast), then I needed to run the patch one more time, and it installed.
I was wondering if someone could kindly throw some light on this please,
Cut a long story short after contacting sincoder to see if my drone would broadcast remote id, he replied not if itās not implemented in your country,
He told me his patch wonāt broadcast my id, so I was sent all the details etc but the only bit I donāt understand is this 
I was also sent a YouTube link ( shorts video ) in Russian I think, which I translated & screen recorded to English, itās a bit vague
I see a post further up the thread ( which wording is slightly different ) Iāll post the link from above,
I know you have to change the name on the controller but do I have to type everything in thatās in the picture above, Iām real sorry to ask, I would or could post the video but I donāt think itāll go down to well 
thanks
In order to add atti mode to the C button
I deleted the drone name (it kept the name)
Typed atti on and clicked okay
Atti mode was then set.
Thankyou for that, so am I right in saying as itās just for the stronger transmission, do I just run the patch & fcc mod is applied, or do I need to type in that top bar regardless for the fcc transmission, thanks for your reply, 
well appreciated ā¦
Yes thatās it nothing else
Donāt even try the other hacks 
1 Like
Donāt you worry about that, that I will not 
Thanks Wayne
Patch applied, not showing RID at least for now anyway.
1 Like
Although I am guessing that it is still on otherwise there wouldnāt be an additional option to turn it off. 